Network Working Group                                        P. Faltstrom
Request for Comments: 2916                             Cisco Systems Inc.
Category: Standards Track                                  September 2000


                          E.164 number and DNS

 Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

 Copyright Notice

   Copyright (C) The Internet Society (2000).  All Rights Reserved.

 Abstract

   This document discusses the use of the Domain Name System (DNS) for
   storage of E.164 numbers.  More specifically, how DNS can be used for
   identifying available services connected to one E.164 number.
   Routing of the actual connection using the service selected using
   these methods is not discussed.

1. Introduction

   Through transformation of E.164 numbers into DNS names and the use of
   existing DNS services like delegation through NS records, and use of
   NAPTR [1] records in DNS [2] [3], one can look up what services are
   available for a specific domain name in a decentralized way with
   distributed management of the different levels in the lookup process.

1.1 Terminology

   The key words "MUST", "REQUIRED", "SHOULD", "RECOMMENDED", and "MAY"
   in this document are to be interpreted as described in RFC 2119 [4].

2. E.164 numbers and DNS

   The domain "e164.arpa" is being populated in order to provide the
   infrastructure in DNS for storage of E.164 numbers.  In order to
   facilitate distributed operations, this domain is divided into
   subdomains.  Holders of E.164 numbers which want to be listed in DNS





Faltstrom                   Standards Track               [Page 1] [top]

RFC 2916                  E.164 number and DNS            September 2000


   should contact the appropriate zone administrator in order to be
   listed, by examining the SOA resource record associated with the
   zone, just like in normal DNS operations.

   Of course, as with other domains, policies for such listings will be
   controlled on a subdomain basis and may differ in different parts of
   the world.

   To find the DNS names for a specific E.164 number, the following
   procedure is to be followed:

  1.  See that the E.164 number is written in its full form, including
      the countrycode IDDD.  Example: +46-8-9761234

  2.  Remove all non-digit characters with the exception of the leading
      '+'.  Example: +4689761234

  3.  Remove all characters with the exception of the digits.  Example:
      4689761234

  4.  Put dots (".") between each digit.  Example: 4.6.8.9.7.6.1.2.3.4

  5.  Reverse the order of the digits.  Example: 4.3.2.1.6.7.9.8.6.4

  6.  Append the string ".e164.arpa" to the end.  Example:
      4.3.2.1.6.7.9.8.6.4.e164.arpa

2.1 Special note about the '+'

   The '+' is kept in stage 2 in section 2 to flag that the number which
   the regular expression is operating on is a E.164 number.  Future
   work will be needed to determine how other numbering plans (such as
   closed ones) might be identified.  It is possible, but not definite,
   that they would use a similar mechanism as the one described in this
   document.

3. Fetching URIs given an E.164 number

   For a record in DNS, the NAPTR record is used for identifying
   available ways of contacting a specific node identified by that name.
   Specifically, it can be used for knowing what services exists for a
   specific domain name, including phone numbers by the use of the
   e164.arpa domain as described above.

   The identification is using the NAPTR resource record defined for use
   in the URN resolution process, but it can be generalized in a way
   that suits the needs specified in this document.




Faltstrom                   Standards Track               [Page 2] [top]

RFC 2916                  E.164 number and DNS            September 2000


   It is the string which is the result of step 2 in section 2 above
   which is input to the NAPTR algorithm.

3.1 The NAPTR record

   The key fields in the NAPTR RR are order, preference, service, flags,
   regexp, and replacement.  For a detailed description, see:

   o  The order field specifies the order in which records MUST be
      processed when multiple NAPTR records are returned in response to
      a single query.

   o  The preference field specifies the order in which records SHOULD
      be processed when multiple NAPTR records have the same value of
      "order".

   o  The service field specifies the resolution protocol and resolution
      service(s) that will be available if the rewrite specified by the
      regexp or replacement fields is applied.

   o  The flags field contains modifiers that affect what happens in the
      next DNS lookup, typically for optimizing the process.

   o  The regexp field is one of two fields used for the rewrite rules,
      and is the core concept of the NAPTR record.

   o  The replacement field is the other field that may be used for the
      rewrite rule.

   Note that the client applies all the substitutions and performs all
   lookups, they are not performed in the DNS servers.  Note that URIs
   are stored in the regexp field.

3.1.1 Specification for use of NAPTR Resource Records

   The input is an E.164 encoded telephone number.  The output is a
   Uniform Resource Identifier in its absolute form according to the
   'absoluteURI' production in the Collected ABNF found in RFC 2396 [5]

   An E.164 number, without any characters but leading '+' and digits,
   (result of step 2 in section 2 above) is the input to the NAPTR
   algorithm.

   The service supported for a call is E2U.







Faltstrom                   Standards Track               [Page 3] [top]

RFC 2916                  E.164 number and DNS            September 2000


3.1.2 Specification of Service E2U (E.164 to URI)

   * Name: E.164 to URI
   * Mnemonic: E2U
   * Number of Operands: 1
   * Type of Each Operand: First operand is an E.164 number.
   * Format of Each Operand: First operand is the E.164 number in the
     form as specified in step 2 in section 2 in this document.
   * Algorithm: Opaque
   * Output: One or more URIs
   * Error Conditions:
      o E.164 number not in the numbering plan
      o E.164 number in the numbering plan, but no URIs exist for
        that number
      o Service unavailable

   * Security Considerations:
      o Malicious Redirection
        One of the fundamental dangers related to any service such
        as this is that a malicious entry in a resolver's database
        will cause clients to resolve the E.164 into the wrong URI.
        The possible intent may be to cause the client to retrieve
        a resource containing fraudulent or damaging material.
      o Denial of Service
        By removing the URI to which the E.164 maps, a malicious
        intruder may remove the client's ability to access the
        resource.

   This operation is used to map a one E.164 number to a list of URIs.
   The first well-known step in the resolution process is to remove all
   non-digits apart from the leading '+' from the E.164 number as
   described in step 1 and 2 in section 2 of this document.

3.2 Examples

3.2.1 Example 1

$ORIGIN 4.3.2.1.6.7.9.8.6.4.e164.arpa.
   IN NAPTR 100 10 "u" "sip+E2U"    "!^.*$!sip:info@tele2.se!"     .
   IN NAPTR 102 10 "u" "mailto+E2U" "!^.*$!mailto:info@tele2.se!"  .

   This describes that the domain 4.3.2.1.6.7.9.8.6.4.e164.arpa is
   preferably contacted by SIP, and secondly by SMTP.

   In both cases, the next step in the resolution process is to use the
   resolution mechanism for each of the protocols, (SIP and SMTP) to
   know what node to contact for each.




Faltstrom                   Standards Track               [Page 4] [top]

RFC 2916                  E.164 number and DNS            September 2000


3.2.2 Example 2

$ORIGIN 4.3.2.1.6.7.9.8.6.4.e164.arpa.
  IN NAPTR  10 10 "u" "sip+E2U"     "!^.*$!sip:paf@swip.net!"    .
  IN NAPTR 102 10 "u" "mailto+E2U"  "!^.*$!mailto:paf@swip.net!" .
  IN NAPTR 102 10 "u" "tel+E2U"     "!^.*$!tel:+4689761234!"     .

   Note that the preferred method is to use the SIP protocol, but the
   result of the rewrite of the NAPTR record is a URI (the "u" flag in
   the NAPTR record).  In the case of the protocol SIP, the URI might be
   a SIP URI, which is resolved as described in RFC 2543 [6].  In the
   case of the "tel" URI scheme [7], the procedure is restarted with
   this new E.164 number.  The client is responsible for loop detection.

   The rest of the resolution of the routing is done as described above.

3.2.3 Example 3

   $ORIGIN 6.4.e164.arpa.
   * IN NAPTR 100 10 "u" "ldap+E2U" "!^+46(.*)$!ldap://ldap.se/cn=01!" .

   We see in this example that information about all E.164 numbers in
   the 46 countrycode (for Sweden) exists in an LDAP server, and the
   search to do is specified by the LDAP URI [8].

4. IANA Considerations

   This memo requests that the IANA delegate the E164.ARPA domain
   following instructions to be provided by the IAB.  Names within this
   zone are to be delegated to parties according to the ITU
   recommendation E.164.  The names allocated should be hierarchic in
   accordance with ITU Recommendation E.164, and the codes should
   assigned in accordance with that Recommendation.

   Delegations in the zone e164.arpa (not delegations in delegated
   domains of e164.arpa) should be done after Expert Review, and the
   IESG will appoint a designated expert.

5. Security Considerations

   As this system is built on top of DNS, one can not be sure that the
   information one get back from DNS is more secure than any DNS query.
   To solve that, the use of DNSSEC [9] for securing and verifying zones
   is to be recommended.







Faltstrom                   Standards Track               [Page 5] [top]

RFC 2916                  E.164 number and DNS            September 2000


   The caching in DNS can make the propagation time for a change take
   the same amount of time as the time to live for the NAPTR records in
   the zone that is changed. The use of this in an environment where
   IP-addresses are for hire (for example, when using DHCP [11]) must
   therefore be done very carefully.

   There are a number of countries (and other numbering environments) in
   which there are multiple providers of call routing and number/name-
   translation services.  In these areas, any system that permits users,
   or putative agents for users, to change routing or supplier
   information may provide incentives for changes that are actually
   unauthorized (and, in some cases, for denial of legitimate change
   requests).  Such environments should be designed with adequate
   mechanisms for identification and authentication of those requesting
   changes and for authorization of those changes.

6. Acknowledgements

   Support and ideas have come from people at Ericsson, Bjorn Larsson
   and the group which implemented this scheme in their lab to see that
   it worked.  Input has also come from ITU-T SG2, Working Party 1/2
   (Numbering, Routing, Global Mobility and Service Definition), the
   ENUM working group in the IETF, John Klensin and Leif Sunnegardh.

References

   [1]  Mealling, M. and R. Daniel, "The Naming Authority Pointer
        (NAPTR) DNS Resource Record", RFC 2915, September 2000.

   [2]  Mockapetris, P., "Domain names - concepts and facilities", STD
        13, RFC 1034, November 1987.

   [3]  Mockapetris, P., "Domain names - implementation and
        specification", STD 13, RFC 1035, November 1987.

   [4]  Bradner, S., "Key words for use in RFCs to Indicate Requirement
        Levels", BCP 14, RFC 2119, March 1997.

   [5]  Berners-Lee, T., Fielding, R.T. and L. Masinter, "Uniform
        Resource Identifiers (URI): Generic Syntax", RFC 2396, August
        1998.

   [6]  Handley, M., Schulzrinne, H., Schooler, E. and J. Rosenberg,
        "SIP: Session Initiation Protocol", RFC 2543, March 1999.

   [7]  Vaha-Sipila, A., "URLs for Telephone Calls", RFC 2806, April
        2000.




Faltstrom                   Standards Track               [Page 6] [top]

RFC 2916                  E.164 number and DNS            September 2000


   [8]  Howes, T. and M. Smith, "An LDAP URL Format", RFC 1959, June
        1996.

   [9]  Eastlake, D., "Domain Name System Security Extensions", RFC
        2535, March 1999.

   [10] Gulbrandsen, A., Vixie, P. and L. Esibov, "A DNS RR for
        specifying the location of services (DNS SRV)", RFC 2782,
        February 2000.

   [11] Droms, R., "Dynamic Host Configuration Protocol", RFC 2131,
        March 1997.

Author's Address

   Patrik Faltstrom
   Cisco Systems Inc
   170 W Tasman Drive SJ-13/2
   San Jose CA 95134
   USA

   EMail: paf@cisco.com
   URI:   http://www.cisco.com




























Faltstrom                   Standards Track               [Page 7] [top]

RFC 2916                  E.164 number and DNS            September 2000


Appendix A. Scenario

   Say that the content of the e164.arpa zone is the following:

   $ORIGIN e164.arpa.
   6.4 IN NS ns.regulator-e164.example.se.

   The regulator has in turn given a series of 10000 numbers to the
   telco with the name Telco-A. The regulator because of that has in
   his DNS.

   $ORIGIN 6.4.e164.arpa.
   6.7.9.8 IN NS ns.telco-a.example.se.

   A user named Sven Svensson has from Telco A got the phone number
   +46-8-9761234. The user gets the service of running DNS from the
   company Redirection Service.  Sven Svensson has asked Telco A to
   point out Redirection Service as the authoritative source for
   information about the number +46-8-9761234.  Telco A because of this
   puts in his DNS the following.

   $ORIGIN 6.7.9.8.6.4.e164.arpa.
   4.3.2.1 IN NS ns.redirection-service.example.se.

   Sven Svensson has already plain telephony from Telco A, but also a
   SIP service from the company Sip Service which provides Sven with
   the SIP URI "sip:sven@sips.se".  The ISP with the name
   ISP A runs email and webpages for Sven, under the email address
   sven@ispa.se, and URI http://svensson.ispa.se.

   The DNS for the redirection service because of this contains the
   following.

   $ORIGIN 4.3.2.1.6.7.9.8.6.4.e164.arpa.
    IN NAPTR 10 10 "u" "sip+E2U"    "!^.*$!sip:sven@sips.se!"        .
    IN NAPTR 10 10 "u" "mailto+E2U" "!^.*$!mailto:sven@ispa.se!"     .
    IN NAPTR 10 10 "u" "http+E2U"   "!^.*$!http://svensson.ispa.se!" .
    IN NAPTR 10 10 "u" "tel+E2U"    "!^.*$!tel:+46-8-9761234!"       .













Faltstrom                   Standards Track               [Page 8] [top]

RFC 2916                  E.164 number and DNS            September 2000


   A user, John Smith, want to contact Sven Svensson, he to start with
   only has the E.164 number of Sven, i.e. +46-8-9761234.  He takes the
   number, and enters the number in his communication client, which
   happen to know how to handle the SIP protocol.  The client removes
   the dashes, and ends up with the E.164 number +4689761234.  That is
   what is used in the algorithm for NAPTR records, which is as
   follows.

   The client converts the E.164 number into the domain name
   4.3.2.1.6.7.9.8.6.4.e164.arpa., and queries for NAPTR records for
   this domainname.  Using DNS mechanisms which includes following the
   NS record referrals, the following records are returned:

   $ORIGIN 4.3.2.1.6.7.9.8.6.4.e164.arpa.
    IN NAPTR 10 10 "u" "sip+E2U"    "!^.*$!sip:sven@sips.se"        .
    IN NAPTR 10 10 "u" "mailto+E2U" "!^.*$!mailto:sven@ispa.se"     .
    IN NAPTR 10 10 "u" "http+E2U"   "!^.*$!http://svensson.ispa.se" .
    IN NAPTR 10 10 "u" "tel+E2U"    "!^.*$!tel:+46-8-9761234"       .

   Because the client knows sip, the first record above is selected,
   and the regular expression "!^.*$!sip:sven@sips.se" is applied to
   the original string, "+4689761234". The output is "sip:sven@sips.se"
   which is used according to SIP resolution.




























Faltstrom                   Standards Track               [Page 9] [top]

RFC 2916                  E.164 number and DNS            September 2000


Full Copyright Statement

   Copyright (C) The Internet Society (2000).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.



















Faltstrom                   Standards Track              [Page 10] [top]